Ligation sequencing DNA V14 (SQK-LSK114)

Version for device: Flongle

Other available device versions: MinION

1. Tip Introduction to the Ligation Sequencing Kit V14 (SQK-LSK114) protocol

   This protocol describes how to carry out sequencing of a DNA sample using the Ligation Sequencing Kit V14 (SQK-LSK114). It is recommended that a Lambda control experiment is completed first to become familiar with the technology.

   Steps in the sequencing workflow:

   Prepare for your experiment

   You will need to:

   • Extract your DNA, and check its length, quantity and purity. The quality checks performed during the protocol are essential in ensuring experimental success.
   • Ensure you have your sequencing kit, the correct equipment and third-party reagents
   • Download the software for acquiring and analysing your data
   • Check your flow cell to ensure it has enough pores for a good sequencing run

   
   

   Library preparation

   The table below is an overview of the steps required in the library preparation, including timings and optional stopping points.

   Library preparation	Process	Time	Stop option
   DNA repair and end-prep	Repair the DNA and prepare the DNA ends for adapter attachment	35 minutes	4°C overnight
   Adapter ligation and clean-up	Attach the sequencing adapters to the DNA ends	20 minutes	We recommend sequencing your library as soon as it is adapted. DNA library can be stored at 4°C for short-term storage or for repeated use (such as re-loading your flow cell) DNA library can be stored at -80°C for long-term storage.
   Priming and loading the flow cell	Prime the flow cell and load the prepared library for sequencing	5 minutes

   

   Sequencing and analysis

   You will need to:

   • Start a sequencing run using the MinKNOW software which will collect raw data from the device and basecall reads.
   • Start the EPI2ME software and select a bioinformatics workflow to analyse your data.
2. Important Compatibility of this protocol

   This protocol should only be used in combination with:

   • Ligation Sequencing Kit V14 (SQK-LSK114)
   • Control Expansion (EXP-CTL001)
   • Flongle Sequencing Expansion (EXP-FSE002)
   • R10.4.1 Flongle Flow Cells (FLO-FLG114)
   • MinION Mk1B - MinION Mk1B IT requirements document
   • MinION Mk1C - MinION Mk1C IT requirements document
   • GridION - GridION IT requirements document

1. Important Flow cell deterioration/saturation

   At Oxford Nanopore we look to continuously improve our production processes to deliver a more robust product. In the case of Flongle, we are seeing the stability of the flow cells we ship improve. However for a small number of flow cells, upon loading, the flow cell rapidly deteriorates. This can be seen as saturation in the MinKNOW GUI. We are working hard to resolve this, however in the meantime we suggest the following loading recommendations and to use the buffers from the Flongle Sequencing Expansion (EXP-FSE002) shipped with your Flongle flow cells. If you do see rapid deteriorate/saturation on your flow cell, please contact support@nanoporetech.com for assistance.

   Loading recommendations
   Following standard input recommendations, the protocol should produce enough final library (adapted DNA in EB) to load at least two Flongle flow cells. We recommend reserving enough library to load a second Flongle flow cell should you need to generate more data from a second flongle flow cell.

2. Important Flongle Sequencing Expansion (EXP-FSE002)

   There are three buffers that come into direct contact with a flow cell at point of loading (SB: Sequencing Buffer, FCF: Flow Cell Flush and LIB: Library Beads or LIS: Library Solution). When looking at these buffers, we found that there are a very low level of contaminants seeping out of the plastic vials that impacts the robustness of the Flongle flow cell system (MinION and PromethION are not impacted by this).

   We have found that when storing these buffers in glass vials instead of plastic, incidence of deterioration is reduced.

   

   To rapidly deploy this to Flongle users, we have produced a Flongle Sequencing Expansion (EXP-FSE002) with these three components in glass vials, which can perform 12 Flongle flow cell loads in total.

   To load a library onto your Flongle flow cell, you will need to use the following components:

   Flongle Sequencing Expansion (EXP-FSE002) components
   - Sequencing Buffer (SB)
   - Flow Cell Flush (FCF)
   - Library Beads (LIB) or Library Solution (LIS)

   Sequencing Kit components
   - Flow Cell Tether (FCT)

   Oxford Nanopore Technologies deem the useful life of the Flow Cell Expansion to be 6 months from receipt by the customer.

3. Adjust your sample input quantity depending on your initial DNA sample length:

   Fragment library length	Starting input
   Very short (<1 kb)	50 fmol
   Short (1-10 kb)	50–100 fmol
   Long (>10 kb)	500 ng

   Users can start with lower input quantities (down to 50 ng) if performing DNA fragmentation to increase the number of DNA molecules in the sample, or if amplifying the sample by PCR.

   For more information on sample input and flow cell loading amounts for our ligation sequencing protocols please visit our know-how document.

4. Input DNA

   How to QC your input DNA

   It is important that the input DNA meets the quantity and quality requirements. Using too little or too much DNA, or DNA of poor quality (e.g. highly fragmented or containing RNA or chemical contaminants) can affect your library preparation.

   For instructions on how to perform quality control of your DNA sample, please read the Input DNA/RNA QC protocol.

   Chemical contaminants

   Depending on how the DNA is extracted from the raw sample, certain chemical contaminants may remain in the purified DNA, which can affect library preparation efficiency and sequencing quality. Read more about contaminants on the Contaminants page of the Community.

5. NEBNext® Companion Module v2 for Oxford Nanopore Technologies® Ligation Sequencing

   We recommend buying the NEBNext® Companion Module v2 for Oxford Nanopore Technologies® Ligation Sequencing (catalogue number E7672S or E7672L), which contains all the NEB reagents needed for use with the Ligation Sequencing Kit.

   The previous version, NEBNext® Companion Module for Oxford Nanopore Technologies® Ligation Sequencing (NEB, E7180S or E7180L) is compatible, but the recommended v2 module offers more efficient dA-tailing and ligation, a result of the FFPEv2 DNA Repair Buffer and Salt-T4 DNA Ligase, respectively. A marked cost saving per sample preparation is also realised when using the v2 module.

   Note: for our amplicon protocols, NEBNext FFPE DNA Repair Mix is not required and purchasing the required reagents separately is more cost effective.

6. Third-party reagents

   We have validated and recommend the use of all the third-party reagents used in this protocol. Alternatives have not been tested by Oxford Nanopore Technologies.

   For all third-party reagents, we recommend following the manufacturer's instructions to prepare the reagents for use.

7. Check your flow cell

   We highly recommend that you check the number of pores in your flow cell prior to starting a sequencing experiment. This should be done within 12 weeks of purchasing for MinION/GridION/PromethION or within four weeks of purchasing Flongle Flow Cells. Oxford Nanopore Technologies will replace any flow cell with fewer than the number of pores in the table below, when the result is reported within two days of performing the flow cell check, and when the storage recommendations have been followed. To do the flow cell check, please follow the instructions in the Flow Cell Check document.

   Flow cell	Minimum number of active pores covered by warranty
   Flongle Flow Cell	50
   MinION/GridION Flow Cell	800
   PromethION Flow Cell	5000

8. Important We strongly recommend using the Ligation Buffer (LNB) supplied in the Ligation Sequencing Kit V14 rather than any third-party ligase buffers to ensure high ligation efficiency of the Ligation Adapter (LA).
9. Important Ligation Adapter (LA) included in this kit and protocol is not interchangeable with other sequencing adapters.
10. Ligation Sequencing Kit V14 (SQK-LSK114) contents

    Note: We are in the process of reformatting our kits with single-use tubes into a bottle format.

    Single-use tubes format:
    

    Bottle format:
    

    Note: This Product Contains AMPure XP Reagent Manufactured by Beckman Coulter, Inc. and can be stored at -20°C with the kit without detriment to reagent stability.

    Note: The DNA Control Sample (DCS) is a 3.6 kb standard amplicon mapping the 3' end of the Lambda genome.

11. Flongle Sequencing Expansion (EXP-FSE002) contents

    

    Name	Acronym	Cap colour	Number of vials	Fill volume per vial (µl)
    Sequencing Buffer	SB	Blue	1	250
    Library Beads	LIB	Blue	1	200
    Library Solution	LIS	Blue	1	200
    Flow Cell Flush	FCF	Blue	1	1,600

    Oxford Nanopore Technologies deem the useful life of the Flow Cell Expansion to be 6 months from receipt by the customer.

12. Important Please note that Oxford Nanopore Technologies deem the useful life of the Flongle Sequencing Expansion (EXP-FSE002) to be 6 months from receipt by the customer.

1. Tip We recommend using the NEBNext® Companion Module v2 for Oxford Nanopore Technologies® Ligation Sequencing (catalogue number E7672S or E7672L), which contains all the NEB reagents needed for use with the Ligation Sequencing Kit.

   The previous version, NEBNext® Companion Module for Oxford Nanopore Technologies® Ligation Sequencing (NEB, E7180S or E7180L) is also compatible, but the recommended v2 module offers more efficient dA-tailing and ligation.

2. Check your flow cell.

   We recommend performing a flow cell check before starting your library prep to ensure you have a flow cell with enough pores for a good sequencing run.

   See the flow cell check instructions in the MinKNOW protocol for more information.

3. Important Flow cell deterioration/saturation

   At Oxford Nanopore we look to continuously improve our production processes to deliver a more robust product. In the case of Flongle, we are seeing the stability of the flow cells we ship improve. However for a small number of flow cells, upon loading, the flow cell rapidly deteriorates. This can be seen as saturation in the MinKNOW GUI. We are working hard to resolve this, however in the meantime we suggest the following loading recommendations and to use the buffers from the Flongle Sequencing Expansion (EXP-FSE002) shipped with your Flongle flow cells. If you do see rapid deteriorate/saturation on your flow cell, please contact support@nanoporetech.com for assistance.

   Loading recommendations
   Following standard input recommendations, the protocol should produce enough final library (adapted DNA in EB) to load at least two Flongle flow cells. We recommend reserving enough library to load a second Flongle flow cell should you need to generate more data from a second flongle flow cell.

4. Important Flongle Sequencing Expansion (EXP-FSE002)

   There are three buffers that come into direct contact with a flow cell at point of loading (SB: Sequencing Buffer, FCF: Flow Cell Flush and LIB: Library Beads or LIS: Library Solution). When looking at these buffers, we found that there are a very low level of contaminants seeping out of the plastic vials that impacts the robustness of the Flongle flow cell system (MinION and PromethION are not impacted by this).

   We have found that when storing these buffers in glass vials instead of plastic, incidence of deterioration is reduced.

   

   To rapidly deploy this to Flongle users, we have produced a Flongle Sequencing Expansion (EXP-FSE002) with these three components in glass vials, which can perform 12 Flongle flow cell loads in total.

   To load a library onto your Flongle flow cell, you will need to use the following components:

   Flongle Sequencing Expansion (EXP-FSE002) components
   - Sequencing Buffer (SB)
   - Flow Cell Flush (FCF)
   - Library Beads (LIB) or Library Solution (LIS)

   Sequencing Kit components
   - Flow Cell Tether (FCT)

   Oxford Nanopore Technologies deem the useful life of the Flow Cell Expansion to be 6 months from receipt by the customer.

5. Thaw DNA Control Sample (DCS) at room temperature, spin down, mix by pipetting, and place on ice.
6. Prepare the NEB reagents in accordance with manufacturer’s instructions, and place on ice.

   For optimal performance, NEB recommend the following:

   1. Thaw all reagents on ice.

   2. Flick and/or invert the reagent tubes to ensure they are well mixed.
      
      Note: Do not vortex the FFPE DNA Repair Mix or Ultra II End Prep Enzyme Mix.

   3. Always spin down tubes before opening for the first time each day.

   4. Vortex the FFPE DNA Repair Buffer v2, or the NEBNext FFPE DNA Repair Buffer and Ultra II End Prep Reaction Buffer to ensure they are well mixed.
      Note: These buffers may contain a white precipitate. If this occurs, allow the mixture(s) to come to room temperature and pipette the buffer several times to break up the precipitate, followed by a quick vortex to mix.

   5. The FFPE DNA Repair Buffer may have a yellow tinge and is fine to use if yellow.

7. Prepare the DNA in nuclease-free water:
   • Transfer 500 ng (or 50-100 fmol) input DNA into a 1.5 ml Eppendorf DNA LoBind tube
   • Adjust the volume to 23.5 μl with nuclease-free water
   • Mix thoroughly by flicking the tube to avoid unwanted shearing
   • Spin down briefly in a microfuge

8. In a 0.2 ml thin-walled PCR tube, mix the following:

   Between each addition, pipette mix 10-20 times.

   Reagent	Volume
   DNA from the previous step	23.5 µl
   DNA CS (optional)	0.5 µl
   NEBNext FFPE DNA Repair Buffer v2	3.5 µl
   NEBNext FFPE DNA Repair Mix	1 µl
   Ultra II End-prep Enzyme Mix	1.5 µl
   Total	30 µl

   
   

   If using the previous version of the NEBNext® Companion Module for Oxford Nanopore Technologies® Ligation Sequencing (NEB, E7180S or E7180L):

   Between each addition, pipette mix 10-20 times.

   Reagent	Volume
   DCS	0.5 µl
   DNA	23.5 µl
   NEBNext FFPE DNA Repair Buffer	1.75 µl
   NEBNext FFPE DNA Repair Mix	1 µl
   Ultra II End-prep Reaction Buffer	1.75 µl
   Ultra II End-prep Enzyme Mix	1.5 µl
   Total	30 µl

9. Thoroughly mix the reaction by gently pipetting and briefly spinning down.
10. Using a thermal cycler, incubate at 20°C for 5 minutes and 65°C for 5 minutes.
11. Resuspend the AMPure XP Beads (AXP) by vortexing.
12. Transfer the DNA sample to a clean 1.5 ml Eppendorf DNA LoBind tube.
13. Add 30 µl of resuspended AMPure XP beads (AXP) to the end-prep reaction and mix by flicking the tube.
14. Incubate on a Hula mixer (rotator mixer) for 5 minutes at room temperature.
15. Prepare 500 μl of fresh 80% ethanol in nuclease-free water.
16. Spin down the sample and pellet on a magnet until supernatant is clear and colourless. Keep the tube on the magnet, and pipette off the supernatant.
17. Keep the tube on the magnet and wash the beads with 200 µl of freshly prepared 80% ethanol without disturbing the pellet. Remove the ethanol using a pipette and discard.
18. Repeat the previous step.
19. Spin down and place the tube back on the magnet. Pipette off any residual ethanol. Allow to dry for ~30 seconds, but do not dry the pellet to the point of cracking.
20. Remove the tube from the magnetic rack and resuspend the pellet in 31 µl nuclease-free water. Incubate for 2 minutes at room temperature.
21. Pellet the beads on a magnet until the eluate is clear and colourless, for at least 1 minute.
22. Remove and retain 31 µl of eluate into a clean 1.5 ml Eppendorf DNA LoBind tube.
23. Quantify 1 µl of eluted sample using a Qubit fluorometer.
24. End of Step Take forward the repaired and end-prepped DNA into the adapter ligation step. However, at this point it is also possible to store the sample at 4°C overnight.

1. Tip We recommend using the Salt-T4® DNA Ligase (NEB, M0467).

   Salt-T4® DNA Ligase (NEB, M0467) can be bought separately or is provided in the NEBNext® Companion Module v2 for Oxford Nanopore Technologies® Ligation Sequencing (catalogue number E7672S or E7672L).

   The Quick T4 DNA Ligase (NEB, E6057) available in the previous version NEBNext® Companion Module for Oxford Nanopore Technologies® Ligation Sequencing (NEB, E7180S or E7180L) is also compatible, but the new recommended reagent offers more efficient and ligation.

2. Important Although third-party ligase products may be supplied with their own buffer, the ligation efficiency of the Ligation Adapter (LA) is higher when using the Ligation Buffer (LNB) supplied in the Ligation Sequencing Kit.
3. Spin down the Ligation Adapter (LA) and Salt-T4® DNA Ligase, and place on ice.
4. Thaw Ligation Buffer (LNB) at room temperature, spin down and mix by pipetting. Due to viscosity, vortexing this buffer is ineffective. Place on ice immediately after thawing and mixing.
5. Thaw the Elution Buffer (EB) at room temperature and mix by vortexing. Then spin down and place on ice.
6. Important Depending on the wash buffer (LFB or SFB) used, the clean-up step after adapter ligation is designed to either enrich for DNA fragments of >3 kb, or purify all fragments equally.
   • To enrich for DNA fragments of 3 kb or longer, use Long Fragment Buffer (LFB)
   • To retain DNA fragments of all sizes, use Short Fragment Buffer (SFB)
7. Thaw either Long Fragment Buffer (LFB) or Short Fragment Buffer (SFB) at room temperature and mix by vortexing. Then spin down and place on ice.
8. In a 1.5 ml Eppendorf DNA LoBind tube, mix in the following order:

   Between each addition, pipette mix 10-20 times.

   Reagent	Volume
   DNA sample from the previous step	30 µl
   Ligation Adapter (LA)	2.5 µl
   Ligation Buffer (LNB)	12.5 µl
   Salt-T4® DNA Ligase	5 µl
   Total	50 µl

9. Thoroughly mix the reaction by gently pipetting and briefly spinning down.
10. Incubate the reaction for 10 minutes at room temperature.
11. Resuspend the AMPure XP Beads (AXP) by vortexing.
12. Add 20 µl of resuspended AMPure XP beads (AXP) to the reaction and mix by flicking the tube.
13. Incubate on a Hula mixer (rotator mixer) for 5 minutes at room temperature.
14. Spin down the sample and pellet on a magnet. Keep the tube on the magnet, and pipette off the supernatant when clear and colourless.
15. Wash the beads by adding either 125 μl Long Fragment Buffer (LFB) or 125 μl Short Fragment Buffer (SFB). Flick the beads to resuspend, then return the tube to the magnetic rack and allow the beads to pellet. Remove the supernatant using a pipette and discard.
16. Repeat the previous step.
17. Spin down and place the tube back on the magnet. Pipette off any residual supernatant. Allow to dry for ~30 seconds, but do not dry the pellet to the point of cracking.
18. Remove the tube from the magnetic rack and resuspend pellet in 7 µl Elution Buffer (EB). Incubate for 10 minutes at room temperature. For high molecular weight DNA, incubating at 37° C can improve the recovery of long fragments.
19. Pellet the beads on a magnet until the eluate is clear and colourless, for at least 1 minute.
20. Remove and retain 7 µl of eluate containing the DNA library into a clean 1.5 ml Eppendorf DNA LoBind tube.

    Dispose of the pelleted beads

21. Quantify 1 µl of eluted sample using a Qubit fluorometer.
22. Prepare your final library to 5-10 fmol in 5 µl of Elution Buffer (EB).

    If required, we recommend using a mass to mol calculator such as the NEB calculator.

23. Important We recommend loading 5-10 fmol of this final prepared library onto the R10.4.1 flow cell.

    Following standard input recommendations, the protocol should produce enough final library (adapter DNA in EB) to load at least two Flongle flow cells. We recommend reserving enough library to load onto a second flow cell. Loading more than 10 fmol can have a detrimental effect on output. Dilute the library in EB or nuclease-free water to a final volume of 5 μl.

24. End of Step The prepared library is used for loading into the flow cell. Store the library on ice or at 4°C until ready to load.
25. Tip Library storage recommendations

    We recommend storing libraries in Eppendorf DNA LoBind tubes at 4°C for short-term storage or repeated use, for example, re-loading flow cells between washes.
    For single use and long-term storage of more than 3 months, we recommend storing libraries at -80°C in Eppendorf DNA LoBind tubes.

1. Important Please note, this kit is only compatible with R10.4.1 flow cells (FLO-FLG114).
2. Important Flongle Sequencing Expansion (EXP-FSE002)

   There are three buffers that come into direct contact with a flow cell at point of loading (SB: Sequencing Buffer, FCF: Flow Cell Flush and LIB: Library Beads or LIS: Library Solution). When looking at these buffers, we found that there are a very low level of contaminants seeping out of the plastic vials that impacts the robustness of the Flongle flow cell system (MinION and PromethION are not impacted by this).

   We have found that when storing these buffers in glass vials instead of plastic, incidence of deterioration is reduced.

   

   To rapidly deploy this to Flongle users, we have produced a Flongle Sequencing Expansion (EXP-FSE002) with these three components in glass vials, which can perform 12 Flongle flow cell loads in total.

   To load a library onto your Flongle flow cell, you will need to use the following components:

   Flongle Sequencing Expansion (EXP-FSE002) components
   - Sequencing Buffer (SB)
   - Flow Cell Flush (FCF)
   - Library Beads (LIB) or Library Solution (LIS)

   Sequencing Kit components
   - Flow Cell Tether (FCT)

   Oxford Nanopore Technologies deem the useful life of the Flow Cell Expansion to be 6 months from receipt by the customer.

3. Important Do NOT touch the reverse side of the Flongle flow cell array or the contact pads on the Flongle adapter. ALWAYS wear gloves when handling Flongle flow cells and adapters to avoid damage to the flow cell or adapter.

   

4. The diagram below shows the components of the Flongle flow cell:

   

   The seal tab, air vent, waste channel, drain port and sample port are visible here. The sample port, drain port and air vent only become accessible once the seal tab is peeled back.

5. Thaw the Sequencing Buffer (SB), Library Beads (LIB) or Library Solution (LIS, if using), Flow Cell Tether (FCT) and Flow Cell Flush (FCF) at room temperature before mixing by vortexing. Then spin down and store on ice.
6. In a fresh 1.5 ml Eppendorf DNA LoBind tube, mix 117 µl of Flow Cell Flush (FCF) with 3 µl of Flow Cell Tether (FCT) and mix by pipetting.
7. Place the Flongle adapter into the MinION or one of the five GridION positions.

   The adapter should sit evenly and flat on the MinION Mk1B or GridION platform. This ensures the flow cell assembly is flat during the next stage.

8. Important The adapter needs to be plugged into your device, and the device should be plugged in and powered on before inserting the Flongle flow cell.

   

9. Place the flow cell into the Flongle adapter, and press the flow cell down until you hear a click.

   The flow cell should sit evenly and flat inside the adapter, to avoid any bubbles forming inside the fluidic compartments.

   

10. Important How to prime and load a Flongle flow cell

11. Peel back the seal tab from the Flongle flow cell, up to a point where the sample port is exposed, as follows:

    1. Lift up the seal tab:
       
       
       

    2. Pull the seal tab to open access to the sample port:
       
       
       

    3. Hold the seal tab open by using adhesive on the tab to stick to the MinION Mk 1B lid:
       

12. To prime your flow cell with the mix of Flow Cell Flush (FCF) and Flow Cell Tether (FCT) that was prepared earlier, ensure that there is no air gap in the sample port or the pipette tip. Place the P200 pipette tip inside the sample port and slowly dispense the 120 µl of priming fluid into the Flongle flow cell by slowly pipetting down. We also recommend twisting the pipette plunger down to avoid flushing the flow cell too vigorously.

    

13. Important The Library Beads (LIB) tube contains a suspension of beads. These beads settle very quickly. It is vital that they are mixed immediately before use.

    We recommend using the Library Beads (LIB) for most sequencing experiments. However, the Library Solution (LIS) is available for more viscous libraries.

14. Vortex the vial of Library Beads (LIB). Note that the beads settle quickly, so immediately prepare the Sequencing Mix in a fresh 1.5 ml Eppendorf DNA LoBind tube for loading the Flongle, as follows:

    Reagents	Volume
    Sequencing Buffer (SB)	15 µl
    Library Beads (LIB) mixed immediately before use, or Library Solution (LIS), if using.	10 µl
    DNA library	5 µl
    Total	30 µl

15. To add the Sequencing Mix to the flow cell, ensure that there is no air gap in the sample port or the pipette tip. Place the P200 tip inside the sample port and slowly dispense the Sequencing Mix into the flow cell by slowly pipetting down. We also recommend twisting the pipette plunger down to avoid flushing the flow cell too vigorously.

    

16. Seal the Flongle flow cell using the adhesive on the seal tab, as follows:

    1. Stick the transparent adhesive tape to the sample port.
       
       
       

    2. Replace the top (Wheel icon section) of the seal tab to its original position.
       

17. End of Step Close the device lid and set up a sequencing run on MinKNOW.

1. How to start sequencing

   Once you have loaded your flow cell, the sequencing run can be started on MinKNOW, our sequencing software that controls the device, data acquisition and real-time basecalling. For more detailed information on setting up and using MinKNOW, please see the MinKNOW protocol.

   MinKNOW can be used and set up to sequence in multiple ways:

   • On a computer either direcly or remotely connected to a sequencing device.
   • Directly on a GridION, MinION Mk1C or PromethION 24/48 sequencing device.

   For more information on using MinKNOW on a sequencing device, please see the device user manuals:

   • MinION Mk1C user manual
   • MinION Mk1B user manual
   • GridION user manual

   ---

   To start a sequencing run on MinKNOW:

   1. Navigate to the start page and click Start sequencing.
   

   2. Fill in your experiment details, such as name and flow cell position and sample ID.
   

   3. Select the sequencing kit used in the library preparation on the Kit page.
   

   4. Configure the sequencing parameters for your sequencing run or keep to the default settings on the Run options and Analysis tabs.

   Note: If basecalling was turned off when a sequencing run was set up, basecalling can be performed post-run on MinKNOW. For more information, please see the MinKNOW protocol.

   5. On the Output page, set up the output parameters or keep to the default settings.
   

   6. Click Start on the Review page to start the sequencing run.
   

2. Duplex basecalling

   Kit 14 chemistry has improved duplex basecalling which requires rebasecalling on Dorado after simplex basecalling has been performed on MinKNOW.

   For detailed information on setting up your sequencing run, for both simplex and duplex basecalling, please see the Kit 14 sequencing and duplex basecalling info sheet.

   Note: When running Dorado, we recommend stopping other basecalling for the best performance by maximising memory available to Dorado. This can be stopped and restarted when Dorado has finished via the GUI on MinKNOW.

3. Data analysis after sequencing

   After sequencing and basecalling, the data can be analysed. For further information about options for basecalling and post-basecalling analysis, please refer to the Data Analysis document.

   In the Downstream analysis section, we outline further options for analysing your data.

1. Below is a list of the most commonly encountered issues, with some suggested causes and solutions.

   We also have an FAQ section available on the Nanopore Community Support section.

   If you have tried our suggested solutions and the issue still persists, please contact Technical Support via email (support@nanoporetech.com) or via LiveChat in the Nanopore Community.

2. Low sample quality

   Observation	Possible cause	Comments and actions
   Low DNA purity (Nanodrop reading for DNA OD 260/280 is <1.8 and OD 260/230 is <2.0–2.2)	The DNA extraction method does not provide the required purity	The effects of contaminants are shown in the Contaminants document. Please try an alternative extraction method that does not result in contaminant carryover. Consider performing an additional SPRI clean-up step.
   Low RNA integrity (RNA integrity number <9.5 RIN, or the rRNA band is shown as a smear on the gel)	The RNA degraded during extraction	Try a different RNA extraction method. For more info on RIN, please see the RNA Integrity Number document. Further information can be found in the DNA/RNA Handling page.
   RNA has a shorter than expected fragment length	The RNA degraded during extraction	Try a different RNA extraction method. For more info on RIN, please see the RNA Integrity Number document. Further information can be found in the DNA/RNA Handling page. We recommend working in an RNase-free environment, and to keep your lab equipment RNase-free when working with RNA.

3. Low DNA recovery after AMPure bead clean-up

   Observation	Possible cause	Comments and actions
   Low recovery	DNA loss due to a lower than intended AMPure beads-to-sample ratio	1. AMPure beads settle quickly, so ensure they are well resuspended before adding them to the sample. 2. When the AMPure beads-to-sample ratio is lower than 0.4:1, DNA fragments of any size will be lost during the clean-up.
   Low recovery	DNA fragments are shorter than expected	The lower the AMPure beads-to-sample ratio, the more stringent the selection against short fragments. Please always determine the input DNA length on an agarose gel (or other gel electrophoresis methods) and then calculate the appropriate amount of AMPure beads to use.
   Low recovery after end-prep	The wash step used ethanol <70%	DNA will be eluted from the beads when using ethanol <70%. Make sure to use the correct percentage.

1. Below is a list of the most commonly encountered issues, with some suggested causes and solutions.

   We also have an FAQ section available on the Nanopore Community Support section.

   If you have tried our suggested solutions and the issue still persists, please contact Technical Support via email (support@nanoporetech.com) or via LiveChat in the Nanopore Community.

2. Fewer pores at the start of sequencing than after Flow Cell Check

   Observation	Possible cause	Comments and actions
   MinKNOW reported a lower number of pores at the start of sequencing than the number reported by the Flow Cell Check	An air bubble was introduced into the nanopore array	After the Flow Cell Check it is essential to remove any air bubbles near the priming port before priming the flow cell. If not removed, the air bubble can travel to the nanopore array and irreversibly damage the nanopores that have been exposed to air. The best practice to prevent this from happening is demonstrated in this video.
   MinKNOW reported a lower number of pores at the start of sequencing than the number reported by the Flow Cell Check	The flow cell is not correctly inserted into the device	Stop the sequencing run, remove the flow cell from the sequencing device and insert it again, checking that the flow cell is firmly seated in the device and that it has reached the target temperature. If applicable, try a different position on the device (GridION/PromethION).
   MinKNOW reported a lower number of pores at the start of sequencing than the number reported by the Flow Cell Check	Contaminations in the library damaged or blocked the pores	The pore count during the Flow Cell Check is performed using the QC DNA molecules present in the flow cell storage buffer. At the start of sequencing, the library itself is used to estimate the number of active pores. Because of this, variability of about 10% in the number of pores is expected. A significantly lower pore count reported at the start of sequencing can be due to contaminants in the library that have damaged the membranes or blocked the pores. Alternative DNA/RNA extraction or purification methods may be needed to improve the purity of the input material. The effects of contaminants are shown in the Contaminants Know-how piece. Please try an alternative extraction method that does not result in contaminant carryover.

3. MinKNOW script failed

   Observation	Possible cause	Comments and actions
   MinKNOW shows "Script failed"		Restart the computer and then restart MinKNOW. If the issue persists, please collect the MinKNOW log files and contact Technical Support. If you do not have another sequencing device available, we recommend storing the flow cell and the loaded library at 4°C and contact Technical Support for further storage guidance.

4. Pore occupancy below 40%

   Observation	Possible cause	Comments and actions
   Pore occupancy <40%	Not enough library was loaded on the flow cell	Ensure the correct volume and concentration as stated on the appropriate protocol for your sequencing library is loaded onto the flow cell. Please quantify the library before loading and calculate fmols using tools like the Promega Biomath Calculator, choosing "dsDNA: µg to fmol"
   Pore occupancy close to 0	The Ligation Sequencing Kit was used, and sequencing adapters did not ligate to the DNA	Make sure to use the NEBNext Quick Ligation Module (E6056) and Oxford Nanopore Technologies Ligation Buffer (LNB, provided in the sequencing kit) at the sequencing adapter ligation step, and use the correct amount of each reagent. A Lambda control library can be prepared to test the integrity of the third-party reagents.
   Pore occupancy close to 0	The Ligation Sequencing Kit was used, and ethanol was used instead of LFB or SFB at the wash step after sequencing adapter ligation	Ethanol can denature the motor protein on the sequencing adapters. Make sure the LFB or SFB buffer was used after ligation of sequencing adapters.
   Pore occupancy close to 0	No tether on the flow cell	Tethers are adding during flow cell priming (FLT tube for Kit 9, 10, 11, FCT for Kit 14, and FTU for ultra-long DNA kits). Make sure FLT/FCT/FTU was added to the buffer (FB for Kit 9, 10, 11, and FCF for Kit 14) before priming.

5. Shorter than expected read length

   Observation	Possible cause	Comments and actions
   Shorter than expected read length	Unwanted fragmentation of DNA sample	Read length reflects input DNA fragment length. Input DNA can be fragmented during extraction and library prep. 1. Please review the Extraction Methods in the Nanopore Community for best practice for extraction. 2. Visualise the input DNA fragment length distribution on an agarose gel before proceeding to the library prep. In the image above, Sample 1 is of high molecular weight, whereas Sample 2 has been fragmented. 3. During library prep, avoid pipetting and vortexing when mixing reagents. Flicking or inverting the tube is sufficient.

6. Large proportion of unavailable pores

   Observation	Possible cause	Comments and actions
   Large proportion of unavailable pores (shown as blue in the channels panel and pore activity plot) The pore activity plot above shows an increasing proportion of "unavailable" pores over time.	Contaminants are present in the sample	Some contaminants can be cleared from the pores by the unblocking function built into MinKNOW. If this is successful, the pore status will change to "sequencing pore". If the portion of unavailable pores stays large or increases: 1. A nuclease flush using the Flow Cell Wash Kit (EXP-WSH004) can be performed, or 2. Run several cycles of PCR to try and dilute any contaminants that may be causing problems.

7. Large proportion of inactive pores

   Observation	Possible cause	Comments and actions
   Large proportion of inactive/unavailable pores (shown as light blue in the channels panel and pore activity plot. Pores or membranes are irreversibly damaged)	Air bubbles have been introduced into the flow cell	Air bubbles introduced through flow cell priming and library loading can irreversibly damage the pores. Watch the Priming and loading your flow cell video for best practice
   Large proportion of inactive/unavailable pores	Certain compounds co-purified with DNA	Known compounds, include polysaccharides, typically associate with plant genomic DNA. 1. Please refer to the Plant leaf DNA extraction method. 2. Clean-up using the QIAGEN PowerClean Pro kit. 3. Perform a whole genome amplification with the original gDNA sample using the QIAGEN REPLI-g kit.
   Large proportion of inactive/unavailable pores	Contaminants are present in the sample	The effects of contaminants are shown in the Contaminants Know-how piece. Please try an alternative extraction method that does not result in contaminant carryover.

8. Temperature fluctuation

   Observation	Possible cause	Comments and actions
   Temperature fluctuation	The flow cell has lost contact with the device	Check that there is a heat pad covering the metal plate on the back of the flow cell. Re-insert the flow cell and press it down to make sure the connector pins are firmly in contact with the device. If the problem persists, please contact Technical Services.

9. Failed to reach target temperature

   Observation	Possible cause	Comments and actions
   MinKNOW shows "Failed to reach target temperature"	The instrument was placed in a location that is colder than normal room temperature, or a location with poor ventilation (which leads to the flow cells overheating)	MinKNOW has a default timeframe for the flow cell to reach the target temperature. Once the timeframe is exceeded, an error message will appear and the sequencing experiment will continue. However, sequencing at an incorrect temperature may lead to a decrease in throughput and lower q-scores. Please adjust the location of the sequencing device to ensure that it is placed at room temperature with good ventilation, then re-start the process in MinKNOW. Please refer to this FAQ for more information on MinION temperature control.